24HPOW
24V 2.5A power supply + plug (US)
High power 24V 2.5A power supply + power plug.

Recommended for long cable runs with several high-power wireless cards.
18.88 18.88 USD
48POW
48V 1.46A 70W power adapter + power plug (US)


18.88 18.88 USD
48V2A96W
48 V 2 A 96 W power supply with plug (US), to be used with our products that support 48 V POE output, like hEX PoE and CRS112-8P-4S-IN. It’s providing 30% more current than the old model 48POW (48 V 1.46 A 70 W), allowing more power per port.
39.00 39.0 USD
G1040A-60WF
Hot Swap 12V 60W power supply for CRS504-4XQ-IN, CCR2004-16G-2S+
49.00 49.0 USD
GESP
GESP, surge protector in IP68 enclosure

GESP is Gigabit Ethernet Surge Protector that can be used to protect the network from lightning or surge damage.

Here’s what a typical use case would be like. You have a mast with some antennas. And some switches on the ground. Put the GESP surge protectors on each end. They come sealed inside a new and improved IP67 weatherproof enclosure. Your antennas are now safe during a lightning storm.

Don’t forget about the grounding wire! Secure it to the rackmount, mast, or any other structure that is connected to the ground. For maximum protection, you should use a surge protector on both ends of long cables.
29.28 29.28 USD
K-65
Rackmount ears for RB4011 series, for installing units in standard rack
7.18 7.18 USD
K-79
With this kit you can mount up to four RB5009UG+S+IN routers in a single 1U rackmount space! No more server room-Tetris, just pure productivity.
9.78 9.78 USD
MT-HotSwapFan
Hot Swap Fan for CCR2216-1G-12XS-2XQ
If your fans go out of order at some point, you can swap them without unnecessary downtime, as there is no need to turn the router off
39.00 39.0 USD
MTP250-26V94-OD
While the MTP250-53V47-OD (see related products) can output 53V 250W, the MTP250-26V94-OD works with a 26V 250W output. Both power supplies come in a sturdy IP67 enclosure with extra protection from dust and moisture.

The voltage will depend on your setup – take a look at the “DC jack input Voltage” in the Power input specifications of the desired devices. In our example the home access points are designed for 12-30 V power supplies, so we are using the MTP250-26V94-OD. If you have a setup demanding higher voltage – like a net of PTZ security cameras, you could use the MTP250-53V47-OD instead. Always check the necessary voltage before powering your devices!
99.00 99.0 USD
MTP250-53V47-OD
MTP250-53V47-OD can output 53V 250W, while the MTP250-26V94-OD (see related products) works with a 26V 250W output. Both power supplies come in a sturdy IP67 enclosure with extra protection from dust and moisture.

The voltage will depend on your setup – take a look at the “DC jack input Voltage” in the Power input specifications of the desired devices. In our example the home access points are designed for 12-30 V power supplies, so we are using the MTP250-26V94-OD. If you have a setup demanding higher voltage – like a net of PTZ security cameras, you could use the MTP250-53V47-OD instead. Always check the necessary voltage before powering your devices!
99.00 99.0 USD
RBGPOE-CON-HP
This device lets you use any 48V PoE source (including Passive PoE, Telecom PoE, 802.3af and 802.3at) to power RouterBOARD devices.

Simply plug any 48V PoE powered ethernet cable into one port, and any 8-30V capable RouterBOARD device into the other. This device is capable to provide high power output - up to 24W (up to 1A at 24V).

You can power it with virtually any 42-57V PoE solutions available on market today (Passive, Telecom, 802.3af and 802.3at PoE plus supported)

The device is a rugged metallic design, with high quality components and integrated heatsink design. The case also has mounting holes so you can attach it to a wall.

Ethernet shield pins are inside the Ethernet connectors, so that shielded ethernet can be used, to ground either at the converter itself, or at the devices at both ends. Supports 10/100/1000Mbps Ethernet.
Note: In case if 803.3af compliant PSE is used, total output power should not exceed 12.95w (limited by the 803.3af standard).
31.88 31.88 USD
S-31DLC20D
S-31DLC20D is a 1.25G SFP transceiver with a 1310nm Dual LC connector, for up to 20 kilometer Single Mode fiber connections, with DDM

Units are tested and compatible with RB260GS,RB2011LS, RB2011LS-IN, RB2011UAS-IN, RB2011UAS-RM, RB2011UAS-2HnD, RB2011UAS-2HnD-IN, and CCR1036-12G-4S. Units are compatible with non-MikroTik SFP devices as well.
29.00 29.0 USD
S-3553LC20D
S-35/53LC20D is a pair of SFP transceivers, the S-35LC20D is a 1.25G Single Mode optical SFP module with a LC connector, T1310nm/R1550nm, which works for connections up to 20km and supports DDM. The S-53LC20D is a 1.25G Single Mode optical SFP transceiver with an LC connector,T1550nm/R1310nm, which works for connections up to 20km and supports DDM.

Units are tested and compatible with RB260GS, RB2011LS, RB2011LS-IN, RB2011UAS-IN, RB2011UAS-RM, RB2011UAS-2HnD, RB2011UAS-2HnD-IN CCR1036-12G-4S. Units are compatible with non-MikroTik SFP devices as well.
79.00 79.0 USD
S-85DLC05D
S-85DLC05D is a 1.25G SFP transceiver with a 850nm Dual LC connector, for up to 550 meter Multi Mode fiber connection, with DDM

Units are tested and compatible with RB260GS, RB2011LS, RB2011LS-IN, RB2011UAS-IN, RB2011UAS-RM, RB2011UAS-2HnD, RB2011UAS-2HnD-IN and CCR1036-12G-4S. Units are compatible with non-MikroTik SFP devices as well.
22.00 22.0 USD
S+85DLC03D
S+85DLC03D is a 10G SFP+ transceiver with a LC connector, 850nm, for up to 300 meter Multi Mode fiber connections

Units are tested and compatible with CCR1036-8G-2S+ and CCR1036-8G-2S+EM. Units are compatible with non-MikroTik SFP devices as well.
59.00 59.0 USD
Woobm-USB
The Wireless out-of-band management USB stick (Woobm-USB) is a useful assistant for any network administrator. Simply plug it into any RouterBOARD USB port and it will allow you to access the console of that device over wireless. It sets up as a wireless access point and has a simple web interface where you can access a fully featured terminal interface to configure your router, and where you can configure the Woobm itself.
It can even work as a wireless client: if you wish to manage many devices, just connect all the Woobms to one AP inside your server room and manage the routers through there.

22.78 22.78 USD
SXTR&EP06-A
This device is an absolute staple of affordable connectivity in remote areas. Even if your phone has no reception at all, our SXT LTE6 kit can still deliver due to its advanced LTE chip design and high-gain antenna.

There are two Ethernet ports. Ethernet port #1 has PoE-in. And Ethernet #2 has PoE-out. You can use it to power another device. Fewer cables to worry about in your sweet cabin in the woods!

We’ve included two Micro-SIM slots – for backup. It never hurts to have extra options when it comes to mobile network coverage. Also, the Category 6 LTE modem enables carrier aggregation, allowing SXT to use multiple LTE bands simultaneously. That’s a huge advantage when there are a lot of mobile users in the area. It offers better responsiveness in a crowded environment. And higher efficiency for weaker signal situations in the countryside. Win-win! We have seen Internet speed doubling in rural areas after switching to CAT6, so there is no need to wait for cable network expansions.

When it comes to powering, SXT LTE6 kit supports a wide voltage range of 18-57V with full 802.3af/at compliance.
169.00 169.0 USD
GPeR
The GPeR unit allows extending Ethernet cable by an additional hop (< 100 - 150 m to regular network devices, and up to 210 m to another GPeR unit) up to 1,500 m.

Handy for highrise buildings, and multi-apartment buildings, with many floors and sections, where very long Ethernet cables might be a problem.

The maximum allowed length of CAT6 Ethernet cable between GPeR and power source/router is up to 100 m (depending on cable quality, high quality - up to 150 m).

The maximum allowed distance of CAT6 Ethernet cable between two GPeR devices is up to 210 m (depending on cable quality).

In case if the destination device does not support PoE-in powering, the PoE Passthrough can be disabled by manually removing all jumpers.
33.96 33.96 USD
WMK4011
The RB4011 wall mount kit is made for protecting your device and its ethernet ports from unauthorized access. Made from durable steel, the mount attaches to a wall and allows the ethernet cables to be plugged in before the router is mounted inside. This means that once the device is secured, there is no easy way to unplug cables or move the device.
13.68 13.68 USD